my grill

1. jack123 Saxperience Forum Bum Joined: Mar 2009 bristol Posts: 3385 1.1 desire and a saxo furio!

   #1 28th April 2009, 20:26

   i messed up my grill i think its not flush in one corner and was thinkin should i glue the corner what do you guys and ladies think???
   
   
   
   
   
2. BrightSpark101 L-plater Joined: Jan 2009 Horley Posts: 65 Mk2 Citroen Saxo VTR

   #2 28th April 2009, 20:45

   Are you sure its not just a missing torx screw? if not im not really to sure. If you glue it over time it will weaken and come off again. what about good old cable ties?
3. J222JRA Saxperience Hardcore! Joined: May 2007 Posts: 16839 Saxo VTS, Westfield

   #3 28th April 2009, 20:49

   is it the mesh thats stopping it from sitting flush mate?
   
   I wouldnt advice bonding it in.
4. newqs36 Established Member Joined: Feb 2009 swansea Posts: 1356 vts

   #4 28th April 2009, 21:39

   i had this problem when i did my grill i was forever trimming and refitting. in the end it was that i did not get the part with the screw holes bonded back on properly(i followed a guide on ere somewhere) i ended up going back to the original
5. jack123 Saxperience Forum Bum Joined: Mar 2009 bristol Posts: 3385 1.1 desire and a saxo furio!

   #5 28th April 2009, 22:33

   well i cut off the screw mark on one end and its just cliped in and im just thinkin bout glueing it in one end cus in the middle and on the other side is screwed in so i think it would be on illl look see if there is anywhere to cable tie it but i dont think there is
   
   do you guys think it looks ok like that or do u think i should just get a new one?
6. jack123 Saxperience Forum Bum Joined: Mar 2009 bristol Posts: 3385 1.1 desire and a saxo furio!

   #6 28th April 2009, 22:44

   is my grill mk1 or mk2??
7. J222JRA Saxperience Hardcore! Joined: May 2007 Posts: 16839 Saxo VTS, Westfield

   #7 28th April 2009, 22:46

   mk2 mate
8. jack123 Saxperience Forum Bum Joined: Mar 2009 bristol Posts: 3385 1.1 desire and a saxo furio!

   #8 28th April 2009, 22:51

   ok thanks dude how should i fit that one corner???
9. J222JRA Saxperience Hardcore! Joined: May 2007 Posts: 16839 Saxo VTS, Westfield

   #9 28th April 2009, 22:53

   i would just mess about fitting it mate, mine was an arse but i got there in the end.
10. jack123 Saxperience Forum Bum Joined: Mar 2009 bristol Posts: 3385 1.1 desire and a saxo furio!

    #10 29th April 2009, 07:58

    ill keep tryin i wannt paint it black
11. kirtisb Frequent Poster Joined: Jan 2009 paignton Posts: 650 Mk2 Citroen Saxo VTR

    #11 29th April 2009, 10:07

    i used 5 cable ties for mine as glue was crap. i also had to cut about 2mm off the parts that stick out for where the screw goes it. looks good now and hasnt fell off