Sump bolt torque

1. blake1312 Frequent Poster Joined: May 2009 Bristol :D Posts: 929 Lexus is200

   #1 15th December 2009, 18:37

   How many newton meters does the sump bolt need to be done on a 1.1? and prusme citroen sell the new washers?
   Cheers
2. Sparco_Tom Saxperience Addict Joined: Jan 2007 Aylesbury, Bucks Posts: 12836 Yeaaahh Fiesta

   #2 15th December 2009, 22:51

   sub bolt being which bolt?
3. chris59 Infrequent Poster Joined: Oct 2009 wiltshire Posts: 154 02 plate 1.1 saxo desire

   #3 15th December 2009, 23:31

   think he means sump?
4. Sparco_Tom Saxperience Addict Joined: Jan 2007 Aylesbury, Bucks Posts: 12836 Yeaaahh Fiesta

   #4 15th December 2009, 23:36

   if thats the case, just reuse the old bolt and washer. Tighten it in fully by hand then a good half turn is normally plenty. Just judge by hand

   1 user thanked this post: blake1312
5. yr51ocw Frequent Poster Joined: Oct 2005 Posts: 751

   #5 15th December 2009, 23:44

   sump bolt is 8nm
6. Tontsy Saxperience Addict Joined: Oct 2008 Plymouth, Fiddling - under a two poster ramp Posts: 14064 Audi

   #6 15th December 2009, 23:46

   Quote:

   Originally Posted by yr51ocw sump bolt is 8nm

   hmmm... thats less than finger tight.
7. blake1312 Frequent Poster Joined: May 2009 Bristol :D Posts: 929 Lexus is200

   #7 16th December 2009, 18:08

   hi yh bit of a typo soz and cheers for the help sparco tom, 8nm does seem a bit low buddy....
8. Toms112 Established Member Joined: Dec 2008 Wisbech/Peterborough Posts: 2218 2008 Ford Fiesta ST150

   #8 16th December 2009, 18:12

   What size are the bolts? I would of thought if M8 it'd be 22nm and if M10 about 30ish
9. blake1312 Frequent Poster Joined: May 2009 Bristol :D Posts: 929 Lexus is200

   #9 16th December 2009, 18:30

   Well i have heard its a 8mm square socket needed 2 remove it correct me if im wrong
10. Tontsy Saxperience Addict Joined: Oct 2008 Plymouth, Fiddling - under a two poster ramp Posts: 14064 Audi

    #10 16th December 2009, 18:45

    i cant be bothered to scroll up again, but i beleive tom has said, tighten it up, hand tight, then half a turn again... that would be spot on...and around 28-30Nm anyway.
11. blake1312 Frequent Poster Joined: May 2009 Bristol :D Posts: 929 Lexus is200

    #11 16th December 2009, 20:26

    Ok cheers mate, also anyone no rougthly how much oil i will need to fill the 1.1?
    Cheers
12. wanabevtr Newbie Joined: Aug 2009 Posts: 17

    #12 16th December 2009, 21:18

    you need 3.5L of either 15-40 or 10-40 oil plus a filter, a new washer for the drain sump and you will need a sump key and a oil filter wrench
    
    Remember to recycle the used oil and don't dump in in a drain