PEUGEOT 306 XSI axle for saxo??

1. DaCrazyOne Frequent Poster Joined: Sep 2013 Space Posts: 873 JuliustoogyJD

   #1 18th March 2014, 18:20

   Hello need some advise here.
   
   I am looking to poss buy the axle off the PEUGEOT 306 XSI 3 DOOR HATCHBACK 1998cc (1997)
   
   I know as much as the GTI 6 will fit however am not sure if their the same or XSI is the GT or so on no idea here.
   
   Saxperience mebers needed.
   
   Will this fit to a Citroen saxo vts 1.6 16v 2003 disk abs
   
   Also does anyone know if this is abs sensor as I got a few pictures below but not sure if it is.
   
   
   
   
   
   
   
   
   
   I wont be keeping the disks or anything else lol clean up of the bar and axel etc will be done. As looks to be the same as mine is yellow with red bars on it and abs and I cant work out if that is or is not ABS
2. MuZiZZle Saxperience Post Whore Joined: Jul 2011 Newcastle upon Tyne Posts: 7779 Phase 2 VTS , E61 M5

   #2 18th March 2014, 18:37

   bolts straight on, just lash your front struts off and bobs your uncle!
3. Alfie09 Frequent Poster Joined: Feb 2013 Posts: 579

   #3 18th March 2014, 19:19

   Erm no a gti6 or any other 306 rear beam will it fit on a Saxo
4. DaCrazyOne Frequent Poster Joined: Sep 2013 Space Posts: 873 JuliustoogyJD

   #4 18th March 2014, 19:37

   Quote:

   Originally Posted by Alfie09 Erm no a gti6 or any other 306 rear beam will it fit on a Saxo

   Thx I have one more inquiry. On ym saxo I have foud the problem however am unsure now if it is the axle or rear right suspension arm/stub axle
   
   On the bottom of it theris a square sort of bolt that is about an inch lower than that other. I also have a little play in it from jacking up and wheel has play in it on both sides. Could this be both rear suspension arm/stub axles and bearings gone and both need replacing to fix..
   
   Would it just be better to replace the whole axle ? will have some pictures if I can get under the car uploaded in a few lol.
5. DaCrazyOne Frequent Poster Joined: Sep 2013 Space Posts: 873 JuliustoogyJD

   #5 18th March 2014, 20:04

   Drivers side that is screwed and squeaking like I got a cat stuck in it when going over bumps lol.
   
   
   
   
   This is passengers side Not sure how or if you can see but the square block on that one is at normal level I think and then drivers side is a lot higher up and almost touching metal on metal. Could this just be the arms and bearings need to be done or axle too due to small amounts of play in it but very small
   
   
6. Quick Saxperience Post Whore Joined: Mar 2003 United Kingdom (England) Posts: 7064

   #6 18th March 2014, 20:21

   You need a 106 axle, not a 306!

   1 user thanked this post: MartinObviously
7. DaCrazyOne Frequent Poster Joined: Sep 2013 Space Posts: 873 JuliustoogyJD

   #7 18th March 2014, 20:49

   Quote:

   Originally Posted by Quick You need a 106 axle, not a 306!

   Ok with that said am now confused as the axle does look to be almost the same but if you are advising different am confused as phoned one place he said 306, 106 and a few other cars. So am totally boggled now.
   
   And regarding me other question about the square parts one being high and one being low and a little play in iver side could that be due to the arms as said or axle ?