Streamline Carbon Fibre Product List

2nd December 2007, 23:33

Hopefully may be of interest to some of you guys.

Please email me at bicstonvillas@msn.com with any questions. Please, please accept these products for what they are . . . the high end of the quality scale, no expense spared on quality of materials and methods used.

Some of the products we have been able to reduce in price, based on reduction in the size of premises of Streamline and now having their own Autoclave oven .

In addition, some products do require minimum order of 5, and with other products that do not, upon request group buys will be considered where possible ie: bonnets, tailgates, roof panels etc

Thanks for your interest and sorry for the delay (I know some of you interested may have sorted things by now).

Streamline Carbon Fibre products available

Peugeot 106 Series 1 & 2, Citreon Saxo Phase 1 & 2, 206 Xsi & C2 Vts

106 S2 & Saxo Phase 1 & 2 debadged (106) 2 piece bonnets & tailgates (106 delocked)

Wet lay process, 2x2 twill carbon outer skin, E glass inner skin = £599.00
Full fibreglass product = £449.00
Autoclave cured product with 2x2 twill carbon inner & outer skins (same quality as external panel) = £799.00

Saxo phase 2 Bonnet grill "open mouth/Smiley"

Autoclave cured product, 2x2 twill with e glass backing = £99.00
Fibreglass product = £39.00

106 S1, S2 & Saxo Phase 1 & 2 Replacement Roofskin Panel (A true replacement panel not stick on !)

Wet Lay process, 2x2 twill carbon E glass mix (panel suitably thick for strength) = £399
Autoclave cured product, 2x2 twill carbon = £599.00
Fibreglass product = £199.00

106 S1, S2, Saxo Phase 1 & 2 "Trackday" interior trim panel "FULL" kit

Includes:

Front door card inserts (106 Rallye template) x2
Rear door cards x2
Rear 3/4 panel trims (in place of rear seatbelt mechanisms) x2 (£18.00)
Rear lower 3/4 panel trims (located by taillight clusters) x2 (Separate = £18.00)
Fuel pump covers (circular diameter of 138mm) x2 (separate as pair = £18.00)
Dashboard glovebox blanking cover x1 (separate = £18.00)
Stereo headunit blanking panel x1 (Separate = £9.00)
Switch panel situated below central heater vents x1, replaces heater controls(106 only) (separate = £9.00)

Autoclave cured, 2x2 twill carbon (finished panel depth is suitably thin) = £249.00

4 x Doorcards only = £199

NEW FINISH = Also available in Wet Lay, 2x2 Twill or plain weave carbon = £179.00

4 x door cards only (no additional trim peices) = £125.00

106 Series 2 door mirror covers

Autoclave cured, 2x2 twill or plain weave carbon = £59.00

Saxo door mirror covers

Autoclave cured, 2x2 twill carbon = £23.00

106 & Saxo 16 valve engine dress kit (5 products in total) Vtr kit includes 3 parts only = £99.00

Includes:

Engine cover (£44.99)
Plenum cover (£39.99)
Brake reservoir cover (£34.99)
Fusebox cover (£34.99)
Ecu cover (£34.99)

Autoclave cured products, 2x2 twill carbon = £169.00 (VTS)

106 S2 Gti & Saxo Vtr/Vts OE tailgate spoilers NEW PRODUCT

Autoclave cured product, 2x2 twill carbon = TBA

Saxo Phase 1 & 2 Open mouth lower bumper insert (replaces OE plastic grill)

Autoclave cured product, 2x2 twill carbon = £129.00
Fibreglass product = £49.00

Saxo Phase 1 headlight "Eyebrows" (priced per pair)

Autoclave cured, 2x2 twill carbon = £18.00

Saxo phase 1 & 2 tail light "eyebrows" (priced per pair)

Autoclave cured, 2x2 twill carbon = £18.00

106 S1, S2 & Saxo Phase 1 & 2 door pillar covers (replacement for OE vinyl trim)

Autoclave cured, 2x2 twill carbon = £20.00

Saxo Phase 1 & 2 Vtr & Vts "Pro Comp Ram cooler" including Green cotton performance cone air filter & fixing kit

Autoclave cured, 2x2 twill carbon = £299.00
Wet lay process, 2x2 twill carbon = £249.00
Fibreglass product = £120.00

Saxo phase 1 & 2 & 106 S1 & S2 door handle covers (S1 106 only requires panel cover, not door handle trim)

autoclave cured, 2x2 twill carbon = £18.00

Saxo/106 centre console (direct replacement for OE part) NEW PRODUCT

Autoclave cured, 2x2 twill carbon = £199.00 (Minimum order of 5 with this product)

106/Saxo TU 16 valve Coilpack cover (replacement for OE part)

Autoclave cured, 2x2 twill carbon = £139.00

206 Xsi & Citreon C2 Vts TU 16 valve Coilpack cover (replacement for OE part)

Autoclave cured, 2x2 twill carbon = £99.00

Saxo Phase 1 & 2, 3 piece "Pro Comp" front door card kit (replacement for OE parts)

Autoclave cured, 2x2 twill carbon = £495.00
Wet lay plain weave or 2x2 twill = £299.00
Fibreglass product = £175.00

106/Saxo/206/C2 TU 16 valve "Prep n Play" Plenum suitable for DCOE.SF & DTH throttle bodies
Minimum order quantity of 5 units
Suitable for use with Green cotton panel filter (supplied seperately).
Maximum air horn length of 40mm
This product can benefit from modified scuttle area but is suitable for use in roadcars also.
Plenum can be pre drilled to your requirement, port spacing would need to be specified.

Autoclave product, 2x2 twill carbon, £199.00
Fibreglass product = £99.00

Throttle body air horn trumpets also available in FULL carbon fibre NEW PRODUCT

Autoclave cured, 2x2 twill, 1 set of 4 trumpets = £119.00

Group buy, 5 sets = £99.00 per set.

Thanks

Bic

2nd December 2007, 23:47

any pics of work that YOU, YOURSELF have done? Regarding any of the parts you have mentioned....

3rd December 2007, 00:05

I'd quite like a full carbon fibre centre console blnking panel tbh..

3rd December 2007, 00:06

Yeah pics would be nice.

3rd December 2007, 00:26

until pics of your own work is up, you could just be another MadMods outlet

3rd December 2007, 00:47

this is streamline on ebay, theres been a few threads about the quality of produce from them

im interested in the doorcards set mate, is that 2x front and 2x rears then?

3rd December 2007, 01:47

link to their ebay shop?

3rd December 2007, 01:51

Quote:

Originally Posted by djrem

link to their ebay shop?

http://stores.ebay.co.uk/STREAMLINE-CARBON

there you go guitar hero

3rd December 2007, 04:14

Inyerested in a roof skin. Would they simply bomd over the original pannel or replace it altother? Any pics of the finish of ythe non autoclaved?

3rd December 2007, 09:56

Also interested in the roofskins. I imagine they just fit in place rather than over?

3rd December 2007, 09:59

i believe they fit in the place of the originals.

a friend of mine has bought some parts off Bic, quality is brillaint, as shown in his maxi 106....

iv already spoken to you mate, and will be getting some closer to xmas..

maybe more that we first discussed

James.G

3rd December 2007, 10:01

Quote:

Originally Posted by vipergfx

http://stores.ebay.co.uk/STREAMLINE-CARBON

there you go guitar hero

i cant rep you but still, cheers

3rd December 2007, 10:39

Do you do MK1 Badboy bonnets?

3rd December 2007, 10:57

same as ^^

3rd December 2007, 10:59

have u got a pic

3rd December 2007, 12:20

Door cards are tempting, would need to see them first

3rd December 2007, 17:58

Any pictures of vtr engine cover?? presume you mean rocker cover?

Very interested! Can I order that seperately, or do you have to order it as part of the 3piece set!

3rd December 2007, 18:11

Craig_VT - To save links nad duplicated pictures, I will ensure pictures of the products currently available follow with great urgency, I fully appreciate these kind of things are worth little without verification of products, I am confident quality will shine thorugh even on a computer screen

. Leave it with me, I dont MAKE anything, mreely involved on templating products, new products and promoting a company that really has no other means of making itself known right now.

James Bristol - Can you explain further ? if you mean a full bespoke product then I am again confident the outlay on developing the pattern would scare you off, unless volume could be confirmed with deposit system, it is something that would take a lot of effort and money at the end of the day. Don't get me wrong, anything can be made, but remember people arent always as willing as the next person to pay what they think is reasonable.

DJ Rem - Understandably, i hope to not be considered that very thing.

Saxo 180 - Pictures to follow shortly. The panel is available in either form, to either bond onto the original (not really where I want to be going with the products in all honesty, but a bit of a carry over from the original inventors, Pro Comp), or a panel can be used to replace the OE panel and bonded and fixed into place. I will get pictures of autoclave cured and wet lay panels for you to see the overall finish.

ViperGFX - Doorcard set is for 4 panels yes, in 2x2 twill and autoclave cured, £199.00 plus delivery or collection for free

Rushy_23 - As above, can be bonded over OE panel or replace metal skin M3 CSL style

Griff - Glad your mate was happy with the bits, look forward to getting some products sold in the future, great news.

Anthony & Dave 1- Currently no Badboy mk1 bonnets, get 5 people willing to pay a deposit and the product can be developed and made for you though.

Dave 1 - What product would you like to see a picture of ?

Hughey - To prevent you having to wait any longer than neccesary, if you look on 106rallye.co.uk and look in the carbon thread in the interior mods section, pictures of door cards there, more to come though.

Thanks for the interest guys, hope the enquiries come to something good too.

Cheers

Bic

1 quick question, do I need to be speaking to Simo about pushing products in this way on the forum ? I am not a trader as such, just didn't want to step on any toes.

3rd December 2007, 18:12

Scorpion - There is currently no engine cover for the VTr, the peice dress kit would only include brake reservoir cover, ecu cover and fuse box cover. I have had osme interest from others about the rocker cover being replaced with a carbon item though, and like i am saying to others, 5 people is all it takes to get a new product on the list, with deposits paid etc.

thanks

Bic

3rd December 2007, 19:18

Quote:

Originally Posted by Bicston

Scorpion - There is currently no engine cover for the VTr, the peice dress kit would only include brake reservoir cover, ecu cover and fuse box cover. I have had osme interest from others about the rocker cover being replaced with a carbon item though, and like i am saying to others, 5 people is all it takes to get a new product on the list, with deposits paid etc.

thanks

Bic

How much would we be looking at if we were to be paying deposit etc.

3rd December 2007, 19:59

I'll await pics, you have my email address and reason for needing it that way!

Cheers

3rd December 2007, 20:36

Quote:

Rushy_23 - As above, can be bonded over OE panel or replace metal skin M3 CSL style

Sounds great mate, I was looking at getting a standard replacement roof with
no sunroof in. But would rather wait for the real deal carbon fibre alternative.

Dont think I will be purchasing one until after new year but I will get in touch
as your pretty much everywhere.

Looking at a full replacement. I imagine they can be easily sprayed up if need be?

3rd December 2007, 20:37

Scorpion - With regard to developing the rocker cover ? well 1 thing I would like to confirm is which style of rocker cover people wanted, because across the Saxo, 106 quiksilver and rallye range, i believe there are a few variants,. so we would need to ascertain the preferred style and with any alterations (breather outlets etc). deposit wise it would be £50 per person, at this stage I would be unsure on final product price, until I could go through things with the pattern maker and we have the actual item to take mould from.

Check out Reverie carbon products and their cam and engine covers, some of those are far more intricate though, so wouldnt be in that price bracket.

Saxo180 - Will do my best this week, what do you mean in what you say ? I am confused lol

Thanks

Bic

3rd December 2007, 20:49

Quote:

Originally Posted by Bicston

Saxo180 - Will do my best this week, what do you mean in what you say ? I am confused lol

Bic

I can't find anyone local that will remove my roof pannel and replace with another, hence the reason I wanted one that bonds over the original.

All explained in my email to you

3rd December 2007, 21:04

Quote:

Originally Posted by Bicston

1 quick question, do I need to be speaking to Simo about pushing products in this way on the forum ? I am not a trader as such, just didn't want to step on any toes.

Im sure he wouldnt have any objection, a Pm wouldnt hurt though just to keep everything above board

Don't think this thread belongs in this section though... I think it will eventually find itself living somewhere else, sales/member discount section maybe?

3rd December 2007, 22:27

Rushy_23 - Sounds great, contact me nearer the time by all means. If you wanted a lighter panel and lose the sunroof, a fibreglass version is available also, although not the fanciest version, lol. I will endeavour to get a carbon panel in place on my car in the new year, to put people's concerns at ease and see the panel in place etc.

Saxo 180 - Ok, I understand now, cheers.

Mystic - Ok, will do, thank you.

CHeers

Bic

3rd December 2007, 22:50

get up pics please

3rd December 2007, 23:04

will be this week yes mate, I have to say the most glamourous product currently sitting there witing for a new home is pre preg autoclaved 3 peice saxo door cards in 2x2 twill, absolutely mint, I will get plenty of pics of those

3rd December 2007, 23:12

Quote:

Originally Posted by Bicston

Rushy_23 - Sounds great, contact me nearer the time by all means. If you wanted a lighter panel and lose the sunroof, a fibreglass version is available also, although not the fanciest version, lol. I will endeavour to get a carbon panel in place on my car in the new year, to put people's concerns at ease and see the panel in place etc.

Not to worry mate as Im in no Rush (no pun intended). Would much prefer a
real carbon fibre one. Plan to get it sprayed up on both sides if possible.

3rd December 2007, 23:18

these are the actual moulded door cards right?,

and not just pieces of carbon to stick over the gaps in a srtipped door?

4th December 2007, 10:38

Quote:

Originally Posted by Bicston

Hughey - To prevent you having to wait any longer than neccesary, if you look on 106rallye.co.uk and look in the carbon thread in the interior mods section, pictures of door cards there, more to come though.

Hey mate, I saw a few threads, the ones I saw were carbon fibre sheets to fill the holes, are these the ones?

4th December 2007, 16:15

Pictures would be ace

4th December 2007, 17:02

Quote:

Originally Posted by seanp06

Pictures would be ace

Agreed!

4th December 2007, 17:30

Rushy - Surely why would you paint the carobn on the outside, looks lovely when alongside black panels too.

My_Vtech_Eater - They are true moulds of the OE panels yes, not flat sheet cut to fit, that is the kit we have branded 'trackday' trim kit. The panels are made up of 3 parts and are very very nice, I will make sure i get plenty of pictures for you 2mrw.

Even i want to see pictures in this thread now, lol

4th December 2007, 18:13

Are the door cards going to look like these???????????

door cards

4th December 2007, 18:29

yes but even better 9dare I say it, depending on your taste) as thje new products are now only produced in 2x2 Twill weave and also autoclave cured, not wet lay, so the finish is like glass and the weave is mint.

Thanks for posting pics for people though Lozza, thanks

Bic

4th December 2007, 18:50

Bic, can you supply me with a piece of CF to cover the hole left by taking out the sunroof? I would then bond the CF panel to the edges of the roof skin. Saves replacing the entire roof!!!

4th December 2007, 19:21

Yes not a problem, if you supply a template, I can even get it trimmed exactly to the dimensions you require. What thickness and what weave etc and finish would you like ?

4th December 2007, 19:25

I will get the tape measure when I next get the opportunity mate.

I know nothing about weave and finish. I'm looking for something cheap, as I'm not that bothered about looks, specially as it's going to be on the roof... Thickness will be determined by robustness I guess. Whatever thickness is required to give it enough strength not to crimple. I suppose somewhere around the 2 - 3mm mark?

4th December 2007, 22:22

saxo mk1 bonnet with a badboy if pos thanks

4th December 2007, 23:52

Toad - well whatever the case I am sure it will be stronger than the OE metal panel which flexes lots ! Yes can do it the same thickness as the roof, as I am sure although not concerned about looks, you would want it to sit flush with the external panel side ?

Dave1 - Can you gather others that may be interested in the product in the style you want ? Would you want it in 2x2 twill carbon or fibreglass ?

5th December 2007, 01:03

I've thought about this mate, but i can't see how I would be able to bond it if it were to sit flush... I was thinking of fitting a CF piece that was a little bigger than the hole, about 10mm in diameter? and then just bond it from the inside. Probably best doing it from the inside, as it won't fly off if something doesn't stick!

I'm not sure how thick the roof skin is. I was assuming it was very thin, like 1mm perhaps? If you have any better ideas I'm all ears matey.

5th December 2007, 11:32

Toad - Well what we could do is, have a template for he peice that is going to fit directly inside the sunroof aperture and then you have 2 options really, go for another peice of carbon that would sit on the underside of the roof (and look a bit like the external plastic moulding that sits around the sunroof on the top of the panel) that kind of spans across the join of the new peice that sits inside the hole and allows it to then bond a) to the new panel and b) to the original roof panel, then from the outisde sitting flush with the rest of the roof ? How does that sound ?

Thanks

Bic

5th December 2007, 14:51

That sounds like a good idea! Do you think the hollow centered piece of CF should be about 20mm in width? So when it's in place, its outter edge would stretch 10mm wider than the main piece of CF, and its inside edge would stretch 10mm shorter than the main piece of CF. Is that pretty much what you are getting at?

5th December 2007, 21:35

Yes mate, Spoken woth Merv about it tongiht, can you please give us the dimensions of the hole in the roof ? As we have a template from the pro comp mould but want to check it, he can do it as one complete type mould with a raised part so it would be one peice, alos give us some info on the hole in the skin as there will be a lip that goes inwards to car i am sure, for added strength etc and also there is the extra bracing to allow for in the sunroof skin, so some pictures would be good. £150 approx for him to do something anyway, but far easier with pics asnd dimensions to confirm price, design and outcome etc.

thanks

Bic

5th December 2007, 22:35

Whats the cheapest you will do a mk1 carbon bonnet or carbon effect. pm me prices please.

5th December 2007, 23:00

Some new info:

OE 106 Series 2 Gti,Rallye, Quiksilver rear spoiler, in 2x2 twill or plain weave carbon, autoclave cured, with fixing threads as per OE spoiler to locate and be fixed by retaining nuts and washers.

£179.00, minimum order of 5, with even more than 5, potential group buy discount can also be arranged

I currently have 3 people wishing to buy the product, just 2 more and it can be put into production and turned around within 2-3 weeks, 50% deposit required.

Flat sheets of Carbon Fibre

1m x 0.66m, 2x2 twill, autoclave cured, 600g carbon layer and thin e glass backing (lighter and thinner)

£100 per sheet

In plain weave or 2x2 twill, wet lay process, £50 per sheet

Saxo Door Mirror baseplates

Taken from OE Saxo door mirror base (orignally by Pro Comp but never put into production, the mould now made up of better materials to allow for autoclaving process giving better durability and finish, as pro Comp carried out all of their work in wet lay up). 2x2 twill, autoclave cured

£79.00 per pair

Saxo 'Pro Comp' moulded front door cards, 3 piece including internal door pocket (Pair)

Having discussed this at length this evening with Mervyn, we have come up with an some alternatives to make them more cost effective.

2x2 twill, E glass backed, autoclave cured = £495.00

2x2 twill or plain weave, E glass backed, wet lay up = £299.00

For the extravagant, full carbon weave throughout, no E glass content = Approx £795.00

Throttle Body inlet trumpets/Air horns (No minimum order)

Depending on specification of diamter & lkength of trumpet, you may be required to supply 1 original aluminum (ideally) part, unless we already have a mould for the size you require.

To allow for pitch variation (distance between the fixing holes where the trumpet mounts to the face of the throttle body intake) the product is a 1 piece product which encompasses a carbon fibre base plate (in replacement of the usual aluminum machined base plate) which is able to be trimmed according to your requirement (Streamline can do this at no extra charge using a drill jig to ensure fixing holes are drilled from the centre of the trumpet).

If we get a minimum of 5 orders for the 'prep n play' throttle body air box/ plenum, 40mm length trumpets would be used with the box and a bulk buy discount can be arranged for people wishing to purchase an airbox and a set of 4 carbon fibre trumpets.

Trumpet/Air horns sets (4 per set)

2x2 twill, autoclave cured, 1 piece design, trimmed to your specification = £119.00

bulk orders of 5 sets = £99.00 per set

'Pro Comp' Ram coolers for the Saxo Vtr & Vts

Available in wet lay up and autoclave cure, plain and 2x2 twill, £299 including Green cotton filter, front finishing scoop, removable service/inspection hatch and hard rubber fixings to mount to the front panel of vehicle.

Please see below and attached comments of pictures i was able to take of parts already in production. In some cases, parts may be untrimmed and also have not received final polishing processes.

Thanks

Bic

2x2 twill carbon fibre raw material . . . 100metre roll

'Pro Comp' Saxo Vtr & vts induction Ram Cooler

Service hatch (underneath) of 'Pro Comp' Ram Cooler

50mm diameter x 40mm length Throttle Body trumpet

Saxo Mirror Baseplate 'Mould' (no product currently available for pictures, coming soon though)

Saxo & 106 door pillar dressings (unpolished items pictured)

Saxo & 106 door handle covers and quarter protectors (unpolished and untrimmed)

Saxo (& 106) 'Pro Comp' 3 piece moulded front door cards (sold in pairs)

'Pro Comp' plain weave wet lay up 106 debadged bonnet

Some of the parts included in the 'Trackday interior trim panel kit'

106 door mirror covers

C2 & 206 xsi TU engine coilpack cover & Prep N Play throttle body airbox

280bhp

5th December 2007, 23:02

VTR Logan - Bonnets are priced at £595.00 for 2x2 twill carbon fibre product, ytou would need to have 5 peiople available with deposits to get the product moulded and into production, turnaround of 2 weeks. I am afraid Streamline do not do carbon effect, only real carbon weave, as well as other composites, kevlars etc etc.

Thanks

Bic

5th December 2007, 23:09

to much for me mate.

5th December 2007, 23:15

would the 106 carbon spoiler fit on the saxo bootlid?
any pics of it???

5th December 2007, 23:21

My_Vtech_Eater - I am not sure if it will fit on the Saxo bootlid, perhaps, although the same applies to interested parties in the Saxo spoiler, all it takes is organising 5 people and that gets the product made and on your car.

There will be pictures of the finished product once 5 people have placed their orders, I have not got the funds to be able to invest ahead of future sales with no guarantee of my money being repaid quickly, hence the 5 people rule that kind of surrounds new products in the future. i invested over £1000 in the mould processes for 106 wing mirror covers, 106 and Saxo vts coilpack and 206 & C2 coilpack covers, with few sales too date unfortunatley, I thought they would have sold much better than they have so far, fingers crossed.

thanks

Bic

5th December 2007, 23:25

Quote:

Originally Posted by djrem

until pics of your own work is up, you could just be another MadMods outlet

You seirously dont know who Bic is? where have you been for the past few years....

5th December 2007, 23:37

LOL, cheers josh

5th December 2007, 23:49

Excellent info Bic, I appreciate that. I well definately go for what you have suggested. The only trouble is that I cannot get you the perfect dimensions until I actually remove the sunroof. The problem with this, is that I'm not 100% sure if you can just pop it back in after removing it... But I can assure, you, I will try to get you this information ASAP.

6th December 2007, 00:28

Toad - Ok, not a problem, I will get the dimensions that Mervyn has and you can tell us if this is close or not, its marked out on the Pro Comp mould for the roof skin you see, but we dont want to trust it, best to make sure first, you arent far away either, so best bet make a trip up 1 Saturday with the car and let Mervyn have a look at it. measure up and then maybe come back the following Saturday to collect the part and then get it bonded in, sounds great in theory, lets hope there are no other obstacles in the way lol

6th December 2007, 00:34

Sure thing Bic. Would it be an issue with the sunroof still all fitted though? I wouldn't want to waste anyone's time... But yeah, I'd be happy to pop in. What's the address of your workplace?

6th December 2007, 00:39

Those door cards are the sex mate, how much did you say for the pair £200?
When can I order?

6th December 2007, 00:41

VTR rocker would be awesome as well, any plans for 1?

6th December 2007, 08:23

I'd Recommend one of the Pro-Comps to anyone

Awesome Piece of kit

6th December 2007, 09:05

Quote:

Originally Posted by Hughey

Those door cards are the sex mate, how much did you say for the pair £200?
When can I order?

I think the prices for the door cards are as follows.

2x2 twill, E glass backed, autoclave cured = £495.00

2x2 twill or plain weave, E glass backed, wet lay up = £299.00

For the extravagant, full carbon weave throughout, no E glass content = Approx £795.00

6th December 2007, 10:07

Toad do you have a rollcage?
Just that carbon when damaged tends to shatter. In an accident if the roof deforms it could cause the carbon panel to break into shards, Personally I would rather have a carbon/kevlar composite as this holds together when damaged - thats what the BTCC cars use and thats why the bodywork seems to rip and flap around after their comings together..
It tends to be a little cheaper too so see what streamline can offer

6th December 2007, 10:38

Nice products Bic

See you down santa pod next year!!

6th December 2007, 11:04

Quote:

Originally Posted by Lozza_vtr

I think the prices for the door cards are as follows.

2x2 twill, E glass backed, autoclave cured = £495.00

2x2 twill or plain weave, E glass backed, wet lay up = £299.00

For the extravagant, full carbon weave throughout, no E glass content = Approx £795.00

cheers mate, might need to save some pennies. They look spot on!

6th December 2007, 12:03

Quote:

Originally Posted by Hughey

cheers mate, might need to save some pennies. They look spot on!

They do look really nice don't they.

Might have to invest in some myself.

6th December 2007, 13:13

Quote:

Originally Posted by KamRacing

Toad do you have a rollcage?
Just that carbon when damaged tends to shatter. In an accident if the roof deforms it could cause the carbon panel to break into shards, Personally I would rather have a carbon/kevlar composite as this holds together when damaged - thats what the BTCC cars use and thats why the bodywork seems to rip and flap around after their comings together..
It tends to be a little cheaper too so see what streamline can offer

Great stuff. Thanks for the tip Kam! I haven't got a rollcage, mainly due to still having a sunroof in.

The cup cage I would like to get cannot fit with the sunroof still in place. So once I get the sunroof out, I can get the cage in.

Bic, what do you think of Kam's suggestions about carbon/kevlar composite?

Cheers.

6th December 2007, 18:03

Amendment to product list:

Also available, the 'Trackday' interior trim kit (Flat carbon sheets) also available in Wet Lay method carbon fibre:

Full kit, 2x2 Twill or plain weave carbon = £179.00

4 x door cards only (no additional trim peices) = £125.00

Pictures of both finishes will be available next week once trimmed etc.

Toad - yes not a problem, you can have basically any material combination you want, mervyn has kevlar in stock in the freezer at the minute, lol.

All these products are available in any finish, gel coat fibreglass, carbon weaves and kevlar weaves and all sorts of mixes of them all.

Thanks

Bic

6th December 2007, 18:29

Where's your location Bic? What Sat will suit you best? Cheers.

6th December 2007, 19:29

Toad - Well if you wanted to meet with mervyn next saturday, I will check with him, I don't need to be there but will try to be if i can.

i am over there again next week sorting through all the bonnet moulds he has and part built products, such as 106 and saxo bonnet skins but need bonding to the braced inner frame etc, so there is plenty more to come, not just for the french either, he even has 4 Nissan Almera bonnets and the mould ffs, lol

Does next Saturday sound ok ?

Thanks

Bic

6th December 2007, 19:37

Some more pictures of the additional tirm panels that complete the Trackday Interior trim kit guys.

106 glovebox panel

106 stereo head unit blanking panel

106 heater control pnael replacement trim

Rear quarter trims (these are templates only, poor quality and unpolished)

All of these parts are available immediately and i also have my own second hand peices for sale along with full flocked dashboard and associated parts, lease PM or email for further details etc should you be interested.

Thanks

Bic

6th December 2007, 19:41

This Sat coming (8th) would be fine Bic, or are you refering to the following Sat? Either way, should be OK. What's your workplace's address so I can see what sort of journey it's going to be?

As you do a lot of bonnet stuff, you could possibly help me with something else while I'm there if you wouldn't mind? I've got a fibreglass bonnet that I need to fit... But as it's so delicate, I need to bonnet pin it in all 4 corners, not just the front. I will remove the original hinges... I don't know how up to the job I am doing it myself. I was hoping someone with some experience with my perticular car might be able to help...

6th December 2007, 19:55

Toad - next Saturday as in the 15th Dec, Streamline are based in Croughton mate, about 2-3 miles off the M40 junction 10.

Mervyn would be happy to fit your bonnet for you if you have the pins and locating parts required and should he need to use any material to fit the panel he has plenty of different goodies at the workshop. Take the bonnet with you and he can size it up and price it for you.

Thanks

Bic

6th December 2007, 20:02

Excellent Bic! The 15th will be fine.

With regard to the bonnet... I was assuming the parts which attach in the engine bay area may need welding or something? But yeah, I'll stick in the boot when I come up.

Do I need to speak to Merv before heading up? What's the postcode of Streamline mate, I'll whack it in the satnav.

6th December 2007, 20:12

I'm interested in 16v cam covers with a coilpack cover too. a 3pc set instead of one big cover.

6th December 2007, 20:31

Toad - i will get you the postcode not a problem, and no no welding needed, maybe some small bespoke brackets, we may be able to convince you to mount if OE style as it can sometimes be a pain mounting it in 4 corners, from a security and practicality point of view.

Alex - Something I have always wanted to invest in but i could only afford investing in the 2 coilpack covers and wing mirror covers to date, along with the risk involved in items not selling etc. Yes the cam covers (later spec would be better too) can be done, as always, 5 people would be required to make it happen, if interest was shown, I would then get the product priced up and go from there then see if the interest is still there.

Toad - the door pillar covers are very thin carbon and with a small amount of bond or a thin layer of 3m double sided sticky sheet, they look fine when on the car, I can get some pictures of them on the car certainly, to give a better idea, things look so different when off and on the car for sure.

6th December 2007, 20:50

I'm deffo interested, I'm sure there are a few more 16v owners who would be interested too

6th December 2007, 21:50

Alex - See who else you can find interest from, doesnt take long to find 5 people tbh who want the same, cambelt covers would also be nice

Some more pictures, mainly Saxo parts too

6th December 2007, 21:53

6th December 2007, 23:55

OK, I'll wait to hear from you next then... Cheers.

7th December 2007, 08:43

Damn wish I still had a saxo/106, them parts look immense!

7th December 2007, 08:55

mk1 bad boy bonnet? how much are rear brows?

7th December 2007, 20:12

How much front mk1 brows and the wing mirror covers.(not the caps)

7th December 2007, 20:22

how much carbon fibre mirrors?

8th December 2007, 07:52

Hi guys, sorry for delay in responing, wing mirror base plates are £79.99 (I will be confirming that they fit the 106 next week also when i put a set on my car) and the rear light eye brows I will get aprice for you today, they are not listed on ebay at the minute and Ihavent got them down on my price list yet.

The bad boy bonnet . . . Do you mean the one in the picture on the previous page, I will also get a price for that today too.

Thanks guys

Cheers

Bic

8th December 2007, 19:13

mk1 front eye brows mate

8th December 2007, 20:05

Hey Bic, hows things going?

Just remembered today that ive completely forgot about taking a pic of the coil pack cover for you to pass on to Mervyn.

Engines not been touched much for a week or 2, but its back on the agenda tomorrow so ill get one sent to you in the evening

9th December 2007, 03:48

Quote:

Originally Posted by Bicston

Dave1 - Can you gather others that may be interested in the product in the style you want ? Would you want it in 2x2 twill carbon or fibreglass ?

How many people do i need ?
i will want the badboy bonnet in carbon i dont know what u mean by 2x2 twill carbon

10th December 2007, 22:57

Seanp06 - i think the eye brow covers re £22.99, i will check with Mervyn for you tomorrow, i dont seem to have them on my list.

Willsy - be much appreciated mate, going to Streamline this Friday again so going to bet taking your PM with me and a pic would be ideal, got to pic a cover up for someone else too

Dave 1 - You would need 5 people for the badboy bonnet, 2x2 twill is the pattern of carbon material weave, it gives the stripey finish, plain weave is just that, plain with no stirpe. Is that ok ?

many thanks

Bic

11th December 2007, 02:13

any pics of the different weave types as some people including myself are confused by all this 2x2 twill chat

11th December 2007, 17:05

do you do a carbon splitter that attaches to the bottom of the front bumper. also do you have a pic of a set of your doorcards in a saxo? front and rear please

12th December 2007, 10:55

My_vtech_eater - Yes not a problem see below

Autoclaved 2x2 twill carbon fibre

wet lay plain weave carbon

Does that help explain it a bit better ?

Grantley1988 - There is currently not a standard fitment splitter available, although there are aftermarket larger carbon ones that I can get ?

Like this ?

With regard to door cards, which ones ? flat sheet or 3 peice moulded ?

Thanks

Bic

12th December 2007, 11:18

How much for carbon fibre bonnet for a mk2 VTR? Any pics ive looked everywhere but very pricey..

12th December 2007, 11:56

Whats the difference Bic between the Autoclaved 2x2 twill carbon fibre and
the wet lay plain weave carbon finish?

The Wet Ley Plain Weave looks a much better finish. If money isnt the main concern
would that be the moulds to go for?

Im still interested in your roof skins (without sunroof), if the fibre glass ones
would do the job I would ideally go for one of those to cut costs. But is fibre
glass more likely to get damaged or crack over the carbon fibre? Dont want
a leaking roof cause some twat leaned on my car in a years time for example lol.

One more question (sorry mate

), are the roof skins simple enough to fit. For
example should a skilled bodyshop be able to fit one with ease or do they take
some special skill to get a correct finish.

Sorry for the questions mate just want to make sure I dont buy something I
wont be happy with.

12th December 2007, 16:02

hard_corejoeboy - all carbon fibre bonnets based on OE design are £595 for wet lay product in either plain weave or 2x2 twill. i will check on Friday if they have the mk 2 without vents etc in. Pictures will come once i know this.

Rushy_23 - It is honestly your prefernce as to waht finish you think looks better, wet lay (wether plain or twill it doesnt matter0 will always turn out as a thicker and heavier panel because the amount of resin and gel coat that is required when using this method of production.

Roofskin wise, i can't really see the true benefit in going through the work involved and cost of removing and refitting a fibreglass skin (unless a true trakc/event car to keep weight down and not bothered about a carbon finish). yes you are correct in that carbon fibre is stronger than fibreglass, but depending how thick the fibreglass is will obviously give greather strength or if very thin (like the single skin panels comapnies are selling designed for securing with 4 pins etc) will mean it is not as strong. Only if the panel was dmaaged (no matter how thick or thin) will it then become porous and then leak in weather.

And yes any good bodyshop will be more than competent at removing your old roofskin and fitting the new, with suitable repairs where neccesary

Hope that helps

Cheers

Bic

12th December 2007, 16:26

Got the passenger door off today, going to weigh it tonight, as a fully trimmed door including glass, exterior handle, mirror and all window mechanism inside it is proper heavy, be very interesting to see the weight per door. Once weighed going to strip it right down and then start working out the best way to get it moulded.

Thanks

Bic

12th December 2007, 17:55

OUCH thats gonna hurt the wallet!!! Any reasons as to why carbon fibre costs so much?

12th December 2007, 18:51

Got ya. If I went for a roofskin it would be sprayed over anyhow so I guess
the Autoclaved 2x2 twill carbon fibre would be more suited as Im not interested
in the finish of the carbon fibre. Once the black paint goes on nobody will know
the difference.

Seems I may as well fork out for that rather than the fibreglass, personally not a fan of fibreglass products at all. Okay, well I will keep an eye out for
progress, when the times comes I will give you a shout regarding the carbon
roofskins Bic mate. Will ask all the details I need then.

12th December 2007, 22:50

Rushy_23 - Cool, no problem

Hard_core - i think it comes a close 2nd to fuel

Bit of an update on stripping mine this evening:

Door fully furnished with glass, electric door mirri, mechanisms all in place etc just in at under 25kg a side

Dashboard, very minimal dashboard with no other sundries or clocks etc, 8kg

Wiring Looms = 15kg (this will be halved next year)

Doors i hope to come in at under 10kg per side in the composite material and with the polycarb windows and gutted doors etc . . .

When we get the roof panel off we will weigh that too in comparison to the carbon replacement, along with getting weights of new bonnet and bootlid

Cheers

Bic

12th December 2007, 23:06

Jez thats what i call stripped out!!!

12th December 2007, 23:11

excessively minimal . . . we are going to show the VAg boys what minimal is all about next year

12th December 2007, 23:43

allways loved the dimma kits on 106's.
i imagine doors will be pretty pricey?

12th December 2007, 23:46

Quote:

Originally Posted by Bicston

excessively minimal . . . we are going to show the VAg boys what minimal is all about next year

Lol, looks great mate.

So is the Dash staying out now i assume?

12th December 2007, 23:56

im getting so geared up for a carbon bonnet now

13th December 2007, 18:32

Vtech eater - I will have more accurate price for the doors tomorrow, not as expensive as most will think tbh.

Josh - Yes i have a vision, like I normally sdo and everyone swears blind i am mad, lol. give it 6 months and you will see the finished article though, i hope, lol.

Predator Vtr - when you going to get into the next gear and want one you think

lol

Cheers

Bic

16th December 2007, 11:48

I have emailed the club team and just waitign for a respone as i have been able to negotiate a discount scheme for club memebers.

5% off on individual orders and 10% on orders of 5 or more (on a group buy basis) - This will be the only saxo club that benefits from the discount, (should it be approved

)
Also there are asome quyality 2nd panels available at the minute, I will get pictures up asap just incase they are to any people's taste etc.

Also weighed the fully stripped down door as a bare panel, it weighed just under 14kg, fully trimmed, 25kg !!!

Are there any people as mad as me on here that would have an interest in composite doors

? I have a detailed costs now and also cost of moulds etc. Will psot shortly.

Cheers

Bic

18th December 2007, 20:05

Quote:

Originally Posted by Bicston

My_vtech_eater - Yes not a problem see below

Autoclaved 2x2 twill carbon fibre

wet lay plain weave carbon

Does that help explain it a bit better ?

Grantley1988 - There is currently not a standard fitment splitter available, although there are aftermarket larger carbon ones that I can get ?

Like this ?

With regard to door cards, which ones ? flat sheet or 3 peice moulded ?

Thanks

Bic

flat sheet please

18th December 2007, 23:35

Grantley - a flat sheet approximately 800mmx600mm and to your requireed thickness is £50 for wet lay carbon or £100 for autoclave cured carbon.

Carbon fibre/Composite doors:

Pair of doors in 2x2 twill or plain weave, wet lay carbon & composite with full inner structure as per OE panel = £1495.00 (with discount to club members etc)

Full carbon inner and outer = £1995.00

GRP = £1195.00

Cheers

Bic

19th December 2007, 09:13

shit the bed Bic, thats a terribly high price lol
I'm sure its about right though realistically

I had the oportunity to look at an old alfa touring car and they saved weight on the doors by drilling holes in every flat part of the door. It weighed virtually nothing and only cost the time in labour

19th December 2007, 16:38

u must b mad - but i like it!!!

Your car will basically be all carbon fibre!!

19th December 2007, 19:58

Kam - lol, yes i need to find some info somewhere to start understanding the whole drilling hole thing which can be terrible if done wrong, but if done right can be strong and lose the weight as you say.

mad . . . erm . . . possibly

28th December 2007, 17:21

some pics of an untrimmed 2x2 twill carbon 106 bonnet

106/Saxo Stack dash surround/fascia

I now have a good stock of readily trimmed carbon number plates too

Carbon steering wheel ? . . .

Cheers

Bic

28th December 2007, 18:16

Bet that wheel cost a small fortune. Damn wish i could win the lotto

28th December 2007, 18:32

can you still see the water temp and oil temp as that fascia looks like it cuts them off

28th December 2007, 18:37

Its for a stack dash mate!! Not a normal one

28th December 2007, 18:47

SeanP - not as much as you think, this one i think would go for a snip of what should normally, as its in the way etc, potentially not suitable for roadcar though as not complete wheel.

Vtech eater - the peice is designed for mounting a stack dash or similar (can be templated to suit of course) so yes using standard clocks would not work.

28th December 2007, 18:52

Quote:

Originally Posted by Bicston

106/Saxo Stack dash surround/fascia

Lewis's by any chance?

28th December 2007, 18:52

How far the workshop from Stockport bic. Wouldnt mind a look and price up off things.

28th December 2007, 19:06

based near Silverstone, junction 15 off M1, what were you after ?

Josh - Yes for lewis

28th December 2007, 19:19

Quote:

Originally Posted by Bicston

Josh - Yes for lewis

Sweet, that looks very neat

What functions do the stack dash's have? PM me if you want, keep this thread on track

28th December 2007, 19:51

stack dashes have all the functions you or I will ever need, just remember to get the road one that requires the additional speed sensor so you can have a working speedo lol

15th January 2008, 23:53

Sexy ?

http://cgi.ebay.co.uk/saxo-streamlin...QQcmdZViewItem

Cheers

Bic

16th January 2008, 00:05

previousy there is a splitter in a picture on this page and the page prior, can anyone possibly tell me which one this is

would be much appreciated

thanksssssss

16th January 2008, 00:15

Really wish I could afford/justify carbon doors

Still saving for one of your roofs Bic. Failing that I'd be interested in a carbon pannel to go where the sunroof was

16th January 2008, 00:24

the splitter is 1 mervyn has at the workshop not sure what but he was going to mould it, unless you were interested in it ?

SAXO180 - at least the doorcards are cheaper than doors lol

Should have the roof panel on mine end of March if we have the time

16th January 2008, 00:29

will it fit the saxo?? i duno what it would look like, im interested lol i think it would look good, like a cross between leon cupra r and ibeza splitter but not sure!! how much would you be after? also any more pics of it please??

19th January 2008, 00:05

I will see if Mervyn still has it and find out its origin and take some lictures tomorrow when at the workshop

Thanks

Bic

19th January 2008, 18:58

Cheers for recommending me to Merv Bic. I've got the car going into the bodyshop on Tuesday for the sunroof panel to be fitted. They're going to fill the edges in once it bonded, so it's flush to the roof. They're then going to re-spray the roof, so it pretty much disappears.

I'll put some pics up when I can, hopefully some folks on here will think about doing the same thing. I think Merv could really do with the work, and it's also well priced and obviously well done. Win win situation.

20th January 2008, 22:44

Biteme - Here is a picture of the rear splitter to match, they came as a pair, Mervyn said you can have them for £85.00 plus postage

Toad - No problem, glad it worked out, yes look forward to seeing the pictures

Cheers

Bic

Oh and here is a picture of Streamline Carbon's Autoclave curing oven so we all know what one is, lol

And some pics of some of the fibreglass/carbon bonnets currently being produced

100% inner and outer pre preg phase 1 saxo bonnet final stages

inner framework

underside of vented phase 2 bonnet

addition of bad boy sections to phase 2 bonnet

Pro Comp pre preg ram coolers with pin holeing, (bag split), would require painting to hide defects or suitable for track cars, or for people that want a great product and not too bothered about finish.

20th January 2008, 23:49

I can see "saxo roof" in the 5th pic. More pics???

20th January 2008, 23:56

its just the mould yes, we are taking my roof panel off this week to get the new mould made for the true replacement roof panel

this is the mould for the bonded on panel that pro Comp first developed

Replacement panel much better, onyl £100 dearer too

We will get weight details too of oe panel etc

21st January 2008, 09:27

What sort of price are you looking for the 'Pro Comp pre preg ram coolers with pin holeing', including delivery ?

21st January 2008, 09:50

Bic id love to see that Mk1 bonnet in its finished form when its done.

I need to replace mine at some stage so i may order one before show season. How much is it going to cost?

21st January 2008, 17:44

hello mate sorry only interested in front one would you part with just the front at all mate?

21st January 2008, 21:12

Raunchz - I will get a price for you tomorrow

Willsy - the full carbon mk1 ? i think mervyn said cheaper than normal as it was a development panel, he is just carrying out last and final bits of prep work so its got a nicefinish, I will get a price for you for that one though, I weighed it tho and its a shade over 3kg for complete bonnet, inner and outer frame

Biteme - yes the front one can be sold seperately, so say £40 plus postage unless you want to collect

21st January 2008, 21:15

Some nice work as always Bic and Mr Melv.

Just looking at the roof, will it sit like the standard one does or will it sit higher?

21st January 2008, 21:41

sorry mate bit steep for me i will just buy an ibeza one for 30 new sorry mate if it was about that id prob buy it depending on where u live! as im southampton

21st January 2008, 21:51

i can ask if he will take £30 ?. Well we are in Northampton so its going to want posting.

Rushy_23 - the replacement roof panel will fit as a direct replacement, with no differnece to the oe panel or the way it fits, sits etc

21st January 2008, 21:52

welcome to ask for me please BUT it wont be yet i do want it but i had a smash 2 days ago and its costing me 1000 as im not claiming so NOT cool lol need some fundage but i do want it

cheers

21st January 2008, 21:53

If I had a lottery win I'd be round ordering loads of goodies for the saxo!!!! Specially the carbon doors !!

21st January 2008, 23:16

the doors will be nice once done trust me, there will be cheaper alternatives too

27th January 2008, 17:14

Bic - any ideas on the price of the 'seconds' pro comp ram air cooler yet? Also, just wandering if you had any 'seconds' carbon coil pack covers for 106 gti/vts?

pm me the prices if you want, thanks.

27th January 2008, 17:32

Bicston:
How much for a Mrk2 Carbon Bonnet or a Fibre glass one?
any pics of those too?
Pm me please

27th January 2008, 22:18

Raunchz - Second prices for ram cooler is £100 which includes brand new scoop that finishes off the front of it and also a brand new inspection cover too. You would need to play about with some fixings to mount the cooler to the slam panel & the filter inside. Which saxo is it for Vtr / Vts ?

Evans - Mk2 Saxo bonnet is £595 in carbon with fibreglass inner frame. 100% fibreglass bonnet is £300.00. Mould is waiting to go into production for the MK2 OE replacement bonnet, but need 5 confirmed orders, otherwise other confirmed orders take priority.

Cheers

Bic

19th February 2008, 23:38

MK2 saxo spoiler mould now complete

8 Valve rocker cover mould being started, and also centre console for Saxo being done too.

Moulds being taken for Carbon fibre Saxo/106 doors

For the 106 owners - Rallye bumper inserts

Cheers

Bic

19th February 2008, 23:41

Have you got any idea of how much the 8 Valve rocker cover will be?

20th February 2008, 19:45

Lozza - 8 Valve rocker cover rrp at £139.99 including new citroen/Peugeot badge and anodised Earls aeroquip fitting for breather.

Thanks

Bic
Streamline Carbon

20th February 2008, 20:18

Sounds good. How long will it be until they will be finished? Is it a direct replacement for the original rocker cover or does it fit over the top of the original?

Thanks for the help. I will be up for one of these.

20th February 2008, 20:21

Any news on my roof pannel yet?

20th February 2008, 21:26

How Much Are Mark 1 Carbon Bonnets Going To Be?

20th February 2008, 21:31

Lozza - They are a direct replacement

Should see the first product from the moould in a fortnight all being well

Saxo180 - What panel did you want ? you havent ordered one have you ?

my_vtech_eater - all of our bonnets start at £595.00

Thanks

BiC
Streamline Carbon

20th February 2008, 22:01

Quote:

Originally Posted by Bicston

Lozza - They are a direct replacement

Should see the first product from the moould in a fortnight all being well

Saxo180 - What panel did you want ? you havent ordered one have you ?

my_vtech_eater - all of our bonnets start at £595.00

Thanks

BiC
Streamline Carbon

Was talking to you about the one at £500 by email. The first gelcoat carbon roof. Do you want payment or a deposit? PM or email me

20th February 2008, 22:07

ah ok yes, no payments until we have the first panel out, not long now though

20th February 2008, 22:46

Quote:

Originally Posted by Bicston

ah ok yes, no payments until we have the first panel out, not long now though

Let me know asap. My bodyshop is waiting

Cheers

23rd February 2008, 22:08

Bit more progress

Centre console carbon fibre gear gaitor surrounds Saxo & 106 - rrp £24.99 - designed to come with up and coming product, centre console in carbon

106

Saxo

8 valve rocker cover ready for release agent application, and then gel coat and laminate for mould, next weekend should have first product

rrp from £119.99

Front & rear bumper inserts for 106 also ready for release agent, rrp £179.99, couple of weeks for mould and first product. Also 106/saxo centre consoles to be flatted and prepared for moulding. We also have Saxo dash centre panel in mould, retaining 12v supply and heater controls, ashtray, top heater vent and stereo aperture all blanked off. Coming real soon

Also doing mould for inside panel of doors on Monday night, making progress, just so time consuming. plenty of new products on the way though

Cheers

Bic

23rd February 2008, 22:10

Stop all this messing about with fiddly little bits and crack on with my roof!!!

23rd February 2008, 22:19

the roof panel is being worked on also, we prefer to make progress with all parts rather then 1 by 1, good things come to those who wait, doors will be out of their moulds before roof anyway, just to tempt you, lol

23rd February 2008, 22:21

Quote:

Originally Posted by Bicston

the roof panel is being worked on also, we prefer to make progress with all parts rather then 1 by 1, good things come to those who wait, doors will be out of their moulds before roof anyway, just to tempt you, lol

haha can't afford your doors but nice try lol

23rd February 2008, 22:35

buy 1 at a time, £599 a side

23rd February 2008, 22:36

Quote:

Originally Posted by Bicston

buy 1 at a time, £599 a side

You paint and fit them for that price and you have a deal

23rd February 2008, 23:13

fitting is straight forward, painting . . . you must know a painter lol

24th February 2008, 10:51

Sorry Bics forgot to email you bud...

How much for rear doorcards and pics of these please?
Looking at the shopping list of whats on offer for more items aswell....

Cheers
Red

24th February 2008, 10:55

Your product range is massive, i like it alot. lol.

24th February 2008, 11:52

bic awesome stuff m8 got some bits and bobs already, cant wait for center console

24th February 2008, 16:42

Rear door cards are £99 rrp plus postage of usually not more than £5.00.

Here is a picture of rear card

Thanks

Bic
Streamline Carbon

24th February 2008, 19:10

Quote:

Originally Posted by Bicston

Rear door cards are £99 rrp plus postage of usually not more than £5.00.

Here is a picture of rear card

Thanks

Bic
Streamline Carbon

Had a quick Kleenez moment there...

I'll be in touch soon mate

Thanks
Red

24th February 2008, 19:36

no problem

24th February 2008, 20:36

do you make a carbon fibre dash trim for a saxo? as in the parts around where the stereo is and the bits around the heater fans?

24th February 2008, 21:50

Yes we do, currently finishing the panel ready to take a mould, again, this product should see the 1st sample in a fortnight or so. It retains the original 12v/cigarette lighter outlet, auxilary switch panel and heater controls. The stereo head unit is blanked (although can obviously be trimmed accordingly for different people's requirements), loses the top heater vent and also loses the ashtray. The panel will fix into place using the original fixing points. Please remember this will be fully formed panel like the original, pre preg, strong & lightweight , not simply a flat sheet fixed to the dash like many will have seen before.

Cost to be confirmed once the 1st product is complete, I would estimate at approx £100ish to be honest, but this will be confirmed soon.

Thanks

Bic
Streamline Carbon

24th February 2008, 22:58

Quote:

Originally Posted by Bicston

Yes we do, currently finishing the panel ready to take a mould, again, this product should see the 1st sample in a fortnight or so. It retains the original 12v/cigarette lighter outlet, auxilary switch panel and heater controls. The stereo head unit is blanked (although can obviously be trimmed accordingly for different people's requirements), loses the top heater vent and also loses the ashtray. The panel will fix into place using the original fixing points. Please remember this will be fully formed panel like the original, pre preg, strong & lightweight , not simply a flat sheet fixed to the dash like many will have seen before.

Cost to be confirmed once the 1st product is complete, I would estimate at approx £100ish to be honest, but this will be confirmed soon.

Thanks

Bic
Streamline Carbon

Sounds deadly, i take it the heater panel is blanked to allow gauges or the likes to be cut into it? Do you make the heater vent surrounds in carbon aswel by any chance? I would be interested in getting a price on these when you have confirmed it. Also, what are the chances of a carbon fibre dial surround?

Cheers dude

24th February 2008, 23:03

the heater panel will be fully trimmed to accept the heater dial and switches etc yes. What do you mean by heater vent surrounds ?

Dial surround ? as in the peice of moulded plastic surrounding the clocks / ifso, yes weh vae this coming through with good progress

24th February 2008, 23:55

Quote:

Originally Posted by Bicston

the heater panel will be fully trimmed to accept the heater dial and switches etc yes. What do you mean by heater vent surrounds ?

Dial surround ? as in the peice of moulded plastic surrounding the clocks / ifso, yes weh vae this coming through with good progress

the heater vent surrounds, like the little plastic trim around the heater vents to the far left and right of the dash on a saxo. ya know the ones i'm talking about??

and about the dial surround, i want one hehe

26th February 2008, 17:05

yes i understand which ones, yes the surround is in on the table waiting to be gel coated with the rest and then laminated

26th February 2008, 17:47

How about a carbon dash. I will be saving for some goodies off you anyway mate

4th March 2008, 23:14

another one here for a dress kit for the VTR engine bay

any news on these, i know you want 5 people but dunno how many have asked

4th March 2008, 23:31

Quote:

Originally Posted by Predator_VTR

another one here for a dress kit for the VTR engine bay

any news on these, i know you want 5 people but dunno how many have asked

Is that the three part kit pred? If so they are listed on the streamline carbon ebay shop.

3 Part Kit

4th March 2008, 23:34

Yes that is the part that is the same for VTr & Vts Lozza, available seperately and part of a kit

4th March 2008, 23:48

so you can get the rocker covers for 8 valve engines now???

just want the 5 piece kit if your thinking about doing a mould for the 8 valve engines??

sorry if im being thick, old age is effecting me

7th March 2008, 02:01

yes 8 valve replacement rocker cover in the process of 1st part being made.

also Saxo spoiler progress, phase 2

7th March 2008, 03:02

you should do a mk1 smiley grill and spoiler all pre pregged up. id buy them

7th March 2008, 09:31

oooo how much for the spoiler??

7th March 2008, 11:24

do you have a peice of carbon fibre panel to replace the switches above the radio?

7th March 2008, 17:49

We do have the mk1 grille available in either carbon or fibreglass, pre preg bonnets are now available at £599 which gives you a pre preg outer skin and fibreglassd inner. the grille will obviously be in pre preg also, i think from memory £99 to £129 or so for the grill, I will check

Saxo spoilers will retail at £199, as a complete original replacement item using oe fixings etc.

Yes I have carbon stereo blanking plates, in pre preg £9.00 each, the actual switch panel can be provided also, for £9.00 i will just need to do a template. We have the complete dash centre console mould being worked on at present, as a complete replacement and retaining all oe fixings, fittingsd, switch recesses etc.

thanks

Bic

7th March 2008, 17:53

Dash Dash Dash?

7th March 2008, 20:23

Liking that spoiler bt would much rather see a nice pic of a roof !

Any chance you can do me a sunroof panel for the time being so I can get the cage in???

8th March 2008, 18:42

we can do you a fibreglass panel to cover the hole yes, £50 plus postage

Be patient, proper products take time

8th March 2008, 18:42

Dash ?

8th March 2008, 18:46

How long until the 8v rocker covers are ready fella? Thanks.

8th March 2008, 18:59

Hi there, just stumbled on this thread
Can you supply me with a panel to fill my centre console and window switches in my mk2 vts, I have had to remove the console due to my quickshift, seen some nice tidy ones but not sure where to get one from, below is a picture of the space i need filling so gives you an idea

Cheers
jam

8th March 2008, 20:31

I could also do with the above

8th March 2008, 20:31

Quote:

Originally Posted by Bicston

Dash ?

Yes mate a carbon dash instead of heavy flocking

9th March 2008, 17:30

What exactly do you want for your window switches ? I don't quite understand, we are doing a replacement centre console as per the original if that is what you mean ?

lol is flocking really that heavy ? lol

8v rocker covers not far away, will be worth the wait we hope

9th March 2008, 18:54

i have nicked this picture from Lewis's project so acknowledgement there something like this

9th March 2008, 21:19

Thats the one above

9th March 2008, 21:44

We can provide flat sheeting to be trimmed and templated as above yes, it is not moulded in anyway

9th March 2008, 21:48

Price mate. How big sheets

9th March 2008, 22:35

How big do you want ? complete sheets start from £99 plus any trimming costs and postage charges, or you can simply send us a cardboard template of what you require and we will trim accordingly. For something like above, you would need the thicker sheets, as oppose to the real lightweight thinner panels we use for doorcards etc. The picture above is of wet lay carbon sheeitn, which is heavier and not as strong as pre preg, it uses more fibreglass and resin than carbon generally. oe replacemnt centre consoles will retail at £199 once complete.

for a couple of peices similar size to above i would expect approx £20-30 including postage. i could get lewis so supply me with the templates to mark out panels for people ?

Looking closer, the bottom peice has an angle in the panel, so a mould would be needed, ideal thing to do is mould off of lewis' panel and then supply from that, would also then be 1 peice part, no screws, bolts etc etc, much nicer to look at then

10th March 2008, 11:01

if you could, that would be great as i really want that centre console in mine as well, rough price?

10th March 2008, 13:09

i would also be interested in the quickshift surround and window switch plate

10th March 2008, 13:18

yer same here, so annoying having the switches flapping around

10th March 2008, 18:52

we've got some interest for this

glad i am not the only one

10th March 2008, 18:57

Quote:

Originally Posted by Bicston

We do have the mk1 grille available in either carbon or fibreglass, pre preg bonnets are now available at £599 which gives you a pre preg outer skin and fibreglassd inner. the grille will obviously be in pre preg also, i think from memory £99 to £129 or so for the grill, I will check

Bic

A Mk1 Carbon Fibre bonnet?
Is this a replacement for use with original fittings or with bonnet pins (i dont want bonnet pins). Also- have you got a weight for it as well.