Oil relocation/Fitting my Mani (Im stuck! pictures)

1. elkoi Frequent Poster Joined: Oct 2010 Staffordshire Posts: 510 Red mk1 Vtr

   #1 8th March 2012, 19:43

   Hey, i've been out fitting my manifold today,
   i've took the old manifold off, relocated the oil filter, & plugged the hole.
   
   But now im left with 4 plugs/ connectors.
   
   I've got a green one, which i assume goes into the top of the mani,
   
   i've got a blue one, that i removed from the bottom of my old mani,
   
   & i have 2 plug/connectors that i removed from the old mk2 filter.
   
   Pictures below! just need to know where all these go, cheers!
   
   
   
   
   
   
   
   
   Apparantly the oil sensor one goes in one of these?
   
   
   Thanks
2. Tontsy Saxperience Addict Joined: Oct 2008 Plymouth, Fiddling - under a two poster ramp Posts: 14064 Audi

   #2 8th March 2012, 19:46

   blue and green are for your lambda sensors.
   it was about 16 months ago i done this so i forgot ... did you not look at where everything went lol.
3. elkoi Frequent Poster Joined: Oct 2010 Staffordshire Posts: 510 Red mk1 Vtr

   #3 8th March 2012, 19:49

   Yeah, i understand the green one goes into the top of the mani, but theres nowhere for the blue one to go :o
4. Tontsy Saxperience Addict Joined: Oct 2008 Plymouth, Fiddling - under a two poster ramp Posts: 14064 Audi

   #4 8th March 2012, 20:10

   Quote:

   Originally Posted by elkoi Yeah, i understand the green one goes into the top of the mani, but theres nowhere for the blue one to go :o

   2nd lamda under the car.
   that wont plug back into the mani - so plug it back in to the loom and then tie it out of the way.
5. elkoi Frequent Poster Joined: Oct 2010 Staffordshire Posts: 510 Red mk1 Vtr

   #5 8th March 2012, 20:13

   Do you have a picture of where i have to plug it?
6. ryza Frequent Poster Joined: May 2010 ipswich Posts: 961 track saxo Daily beemer

   #6 8th March 2012, 20:35

   oil sensor goes in A which should be a plug that a square key will get it out. get the 2nd lambda out of the old manifold, plug it into the blue connector, then tie the lambda out of the way. you also will need a mk1 oil pressure sensor. hope the mani got to you alright aswell mate!
7. Bedford126 Saxperience Post Whore Joined: Jul 2010 Morley, Leeds Posts: 8469 Civic ep3 type r powered by TDI NORTH

   #7 9th March 2012, 01:22

   Quote:

   Originally Posted by ryza oil sensor goes in A which should be a plug that a square key will get it out. get the 2nd lambda out of the old manifold, plug it into the blue connector, then tie the lambda out of the way. you also will need a mk1 oil pressure sensor. hope the mani got to you alright aswell mate!

   A is a core plug.
   
   IIRC the oil sensor screws into a port next to the dip-stick tube retainer bolt hole. Should be a 8mm socket in it the same as you use to drain the oil.
   
   And is that a citroen filter?
   
   
8. elkoi Frequent Poster Joined: Oct 2010 Staffordshire Posts: 510 Red mk1 Vtr

   #8 9th March 2012, 06:52

   Ok, thanks, & yes i got it from citroen