Saxo vts corssover loom quiz

1. KierenCrawford Banned Joined: Nov 2013 Posts: 411

   #1 24th January 2014, 19:06

   Mehhhhhh
2. MartinObviously Saxperience Forum Bum Joined: Dec 2012 Perth Posts: 3665 Peugeot 106 1.1 Turbo Peugeot 106 1.5D Turbo Peuge

   #2 25th January 2014, 00:06

   That yellow coloured one, looks to me like the later style MAP sensor connector it's in the right place and I can't think of a anything else with 3 pin connector near the ECU.
   
   Black one right at the top (2 pin) is the connector a sort of dirty orange/brown colour? That will most likely be for the "charcoal" canister that goes under the wing above the wheel arch liner. It sends power to a small solenoid to allow fuel vapours into the inlet.
   
   
   Out of interest, what are you hoping to achieve? What car are you putting this in and with what engine?
   
   If you need to do loom splicing, REMEMBER, Peugeot wire things up by Pin number NOT colour.

   1 user thanked this post: KierenCrawford
3. KierenCrawford Banned Joined: Nov 2013 Posts: 411

   #3 25th January 2014, 09:54

   Mehhhhhh
4. KierenCrawford Banned Joined: Nov 2013 Posts: 411

   #4 25th January 2014, 09:55

   Mehhhhhhh
5. chompy Established Member Joined: Jan 2008 Scotland Posts: 1764 Because racecar

   #5 25th January 2014, 10:07

   Two for the Altenator, oil something on the front of the block and not sure on the green one.

   1 user thanked this post: KierenCrawford
6. MartinObviously Saxperience Forum Bum Joined: Dec 2012 Perth Posts: 3665 Peugeot 106 1.1 Turbo Peugeot 106 1.5D Turbo Peuge

   #6 25th January 2014, 10:27

   The green one is for oil LEVEL sensor, and the reddish one is for the pressure switch right above it.
   
   As chompy says, the 2 ring terminals are for the alternator.
7. KierenCrawford Banned Joined: Nov 2013 Posts: 411

   #7 25th January 2014, 15:02

   Mehhhhhhh
8. KierenCrawford Banned Joined: Nov 2013 Posts: 411

   #8 25th January 2014, 15:04

   Mehhhh
9. MartinObviously Saxperience Forum Bum Joined: Dec 2012 Perth Posts: 3665 Peugeot 106 1.1 Turbo Peugeot 106 1.5D Turbo Peuge

   #9 25th January 2014, 18:27

   I am stumped, can you zoom out a bit so I can see where on the loom it is?
   
   I think the 2 ring terminals are gearbox earths, one plug for your speedo and the other for the gearbox reverse sensor.
   
   But that leaves one I can't work out - so the other 2 could be wrong. :fuck:
10. chompy Established Member Joined: Jan 2008 Scotland Posts: 1764 Because racecar

    #10 25th January 2014, 18:34

    I think the other one is the water temperature sensor. Think.
11. Brendanp Frequent Poster Joined: Mar 2009 Posts: 649

    #11 25th January 2014, 19:02

    Aren't those ring terminals for the starter motor?
    
    Plugs maybe injectors and 2 inlet ones?
12. Tom5190 Saxperience Post Whore Joined: Sep 2007 Someones Bumhole Posts: 5721 Mk2 16v Desire

    #12 25th January 2014, 19:25

    2 x starter ring terminals
    1 x knock sensor
    1 x speedo sensor
    
    Is that a blue or green plug I cant tell from photo?
13. KierenCrawford Banned Joined: Nov 2013 Posts: 411

    #13 25th January 2014, 19:53

    Mehhhh
14. user_7 Frequent Poster Joined: Dec 2002 United Kingdom Posts: 700 Mk6 Golf GTD Saxo VTS Project Rally Car

    #14 25th January 2014, 21:18

    Green, injectors plug?
15. Tom5190 Saxperience Post Whore Joined: Sep 2007 Someones Bumhole Posts: 5721 Mk2 16v Desire

    #15 26th January 2014, 11:48

    Black is knock, grey is speedo. Green is injectors.
    
    How old is the engine you have? That grey MAP sensor plug wont be right for most single plug engines I'd double check it, you may find that some of the plugs don't fit.

    1 user thanked this post: MartinObviously
16. KierenCrawford Banned Joined: Nov 2013 Posts: 411

    #16 26th January 2014, 13:10

    Mehhhhhh
17. KierenCrawford Banned Joined: Nov 2013 Posts: 411

    #17 26th January 2014, 13:19

    Menhhh
18. KierenCrawford Banned Joined: Nov 2013 Posts: 411

    #18 26th January 2014, 13:21

    Mehhhhh
19. Brendanp Frequent Poster Joined: Mar 2009 Posts: 649

    #19 26th January 2014, 14:46

    Black/ blue rubber 4 pin is ICV
    Black /green rubber 3 pin is TPS
    
    Not sure between the other two
    Throttle body heater
    IAT
    
    These are educated guesses using Autodata
20. Brendanp Frequent Poster Joined: Mar 2009 Posts: 649

    #20 26th January 2014, 14:48

    forum lag
21. KierenCrawford Banned Joined: Nov 2013 Posts: 411

    #21 26th January 2014, 15:50

    Mehhhh
22. Brendanp Frequent Poster Joined: Mar 2009 Posts: 649

    #22 26th January 2014, 15:52

    Quote:

    Originally Posted by KierenCrawford Okay cheers for the help so the green/blue rubber ones are deffo ICV AND TPS just the other 2 your not sure about ?

    Should be as autodata only shows them to be the only 3 & 4 pins especially with those rubber sleve type plugs and from experience as well.

    1 user thanked this post: KierenCrawford
23. KierenCrawford Banned Joined: Nov 2013 Posts: 411

    #23 26th January 2014, 18:17

    Mahhnn
24. Brendanp Frequent Poster Joined: Mar 2009 Posts: 649

    #24 26th January 2014, 18:19

    What numbers are written on the wires?
25. user_7 Frequent Poster Joined: Dec 2002 United Kingdom Posts: 700 Mk6 Golf GTD Saxo VTS Project Rally Car

    #25 26th January 2014, 19:09

    Blue connector is the sump, although you are missing half the plug ... same as mine :-(
26. KierenCrawford Banned Joined: Nov 2013 Posts: 411

    #26 26th January 2014, 20:08

    Mehhhhh
27. user_7 Frequent Poster Joined: Dec 2002 United Kingdom Posts: 700 Mk6 Golf GTD Saxo VTS Project Rally Car

    #27 26th January 2014, 20:29

    mine has, yeah

    1 user thanked this post: KierenCrawford